“Jeeyvee” Environmental Test Chamber can generate & maintain above ambient temp.,below ambient temp.,and humidity. It is specifically designed for application of various testing under low temp.& with control humidity.
APPLICATION
Environmental Test Chamber can generate & maintain above ambient temp.,below ambient temp.,and humidity. It is specifically designed for application of various testing under low temp.& with control humidity.
SALIENT FEATURES
Fully automatic, temp. control-Micro control Based.
Easy to operate.
Top Control Penal.
Obstruction free working space.
Digi. Temp. Indicator & Control (Micro Control)
Sensitive Temperature sensor Pt-100 type.
Floor model.
Castor wheel for easy move ability.
Elegant outlook, enamel painted/powder coated.
Glass door/window to see through.
Forced air circulation.
Humidity Control by dry & wet principal.
Digital Humidity Indication (Optional).
Stainless Steel steam boiler.
Panel Meters- Volt & Ampere.
Suitable for climatic & durable tests.
Auto Water level control.
CONSTRUCTION
The unit is of double walled construction. The exterior chamber is made of mild steel and finished in non corrosive paint or powder coated and interior chamber is made of heavy gauge polished stainless steel. Between two chamber glass-wool /  thermocole  insulation is provided. Glass window/Door is provided to see the operation without disturbing the control condition inside the chamber. An outside metal door with lock is provided. The unit rest on castor wheel.
HEATING
[A] Chamber is heated by long lasting air heater to eliminate failure of heater.
[B] Boiler heater is of immersion type heater.
COOLING
Using hermetically sealed compressor coupled with evaporation coil & fan cooled condenser.
HUMIDITY
Humidity generated by steam injection near the duck from a boiler connected to water tank fitted with water level controller. Humidity set & derived by dry & wet bulb principles by the provided depression chart.
INDICATION & CONTROL
Digital display indication for temperatures. Fully automatic solid state electronic controllers with Pt-100 sensors for both dry & wet bulb controllers are panel type easy for maintenance/service.
CONTROL PANEL
Control panel is provided on the top of the unit consisting of Mains switch, Mains indicator, Ampere meter, Voltmeter, Wet bulb Digital Indicator cum Controller, Wet bulb Indication pilot lamp, Dry bulb Digital Indicator cum Controller, Dry bulb indication pilot lamp (For cooling cycle-heating cycles), Low water level controller fitted and connected through circuit to boiler heater low level pilot lamp (will not glow if water level is below requirements), Door heater switch (Optional), Chamber light switch (Optional).
OPERATING VOLTAGE
230 Volts Single Phase, 50Hz, AC.
TECHNICAL SPECIFICATION
| CAPACITY (Cuft) |
INNER DIMN. IN CMS (H x W x D) |
TEMP. RANGE
ACCU.+/-1 DEG.C |
HUMIDITY RANGE ACCU.+/-3% RH |
INNER CHAMBER |
| 6 Cuft |
70 x 50 x 50 |
10 to 60 Deg. C. |
5%
Above
Ambient
toÂ
95% RH |
Stainless Steel |
| 8 Cuft |
80 x 55 x 50 |
10 to 60 Deg. C. |
Stainless Steel |
| 10 Cuft |
90 x 55 x 55 |
10 to 60 Deg. C. |
Stainless Steel |
| 12 Cuft |
90 x 65 x 58 |
10 to 60 Deg. C. |
Stainless Steel |
| 16 Cuft |
90 x 70 x 70 |
10 to 60 Deg. C. |
Stainless Steel |
N. B.
ENVIRONMENTAL TEST CHAMBER OF OTHER SIZE, LOAD CAPACITY AND TEMP. RANGE CAN BE DESIGNED & SUPPLIED ON REQUEST. - MICROPROCESSOR BASED ENVIRONMENTAL TEST CHAMBER IS ALSO AVAILABLE.
RECOMMANDED ACCESSORIES [OPTIONAL]
* Suitable Voltage Stabilizer * Chamber illumination with programmable timer * Digital Lux Meter * Circular Chart Recorder for Dry & Wet Temp.
